NZS 3404.1:2009 Looseleaf

Steel structures Standard - Materials, fabrication, and construction

This document has been re-assessed by the committee, and judged to still be up to date.

NZS 3404.1 sets out minimum requirements for the selection of materials, corrosion protection systems, and the fabrication, erection and construction of steel structures. It will supersede the relevant provisions in NZS 3404:1997 and will be referenced by NZS 3404.2 to NZS 3404.7 once those parts are complete. This Standard applies to building structures; crane support girders; highway, railway and pedestrian bridges; and composite steel and concrete beams and columns. This Standard is supplied with loose pages with 4 holes punched, suitable for a ring binder with 4 rings.

Table of contents are automatically generated, and may not be 100% accurate.

 

Buy product

Download PDF.
$179.10 NZD (ex GST)Retail
$143.28 NZD (ex GST)Members
Order hardcopy.
$199.00 NZD (ex GST)Retail
$159.20 NZD (ex GST)Members
Subscribe online to this Standard for one year.

Add to cart for pricing

 

Publishing information

Status: CURRENT

Published: 12/10/2009

Pages: 161

Committee:  P3404

This document may make references to other documents. All referenced documents are displayed below.

Standards NZ References:

Overseas Standards References:

  • EN 1991-1-6:2005 Eurocode 1 - Actions on structures – Part 1-6: General actions - Actions during execution
  • AS 1110.2-2000 ISO metric hexagon bolts and screws - Product grades A and B - Screws
  • EN 10025.1:2004 Hot rolled products of structural steels - Part 1 General technical delivery conditions
  • AS 1275-1985 Metric screw threads for fasteners
  • ANSI/AISC 341:2005 Seismic provisions for structural steel buildings
  • JIS G 3193:2005 Dimensions mass and permissible variations of hot rolled steel plates sheets and strip
  • AS 1627.4-2005 Metal finishing - Preparation and pretreatment of surfaces - Abrasive blast cleaning
  • EN 10025.5:2004 Hot rolled products of structural steels - Part 5 Technical delivery conditions for structural steels wi
  • EN 10210.1:2006 Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1 Technical delivery c
  • AS 1111.2-2000 ISO metric hexagon bolts and screws – Product grade C - Screws
  • AS 1576.1-1995 Scaffolding - General requirements
  • ASTM A106/A106M:2008 Standard specification for seamless carbon steel pipe for high temperature service
  • AS 1627.1-2003 Metal finishing - Preparation and pretreatment of surfaces - Removal of oil grease and related contaminat
  • ASTM A514/A514M:2005 Standard specification for high-yield-strength quenched and tempered alloy steel plate suitable for
  • EN 1993-1-1:2005 Eurocode 3 - Design of steel structures – Part 1-1: General rules and rules for buildings
  • AS 1391-2007 Metallic materials – Tensile testing at ambient temperature
  • AS 3894.3-2002 Site testing of protective coatings - Determination of dry film thickness
  • AS 3828:1998 Guidelines for the erection of building steelwork
  • JIS G 3101:2004 Rolled steel for general structure
  • AS 1112.1-2000 ISO metric hexagon nuts - Style 1 – Product grades A and B
  • EN 1090-2:2008 Execution of steel structures and aluminium structures – Part 2: Technical requirements for steel structu
  • EN 10025.2:2004 Hot rolled products of structural steels - Part 2 Technical delivery conditions for non-alloy structural
  • AS 1210-1997 Pressure vessels
  • EN 10025.3:2004 Hot rolled products of structural steels - Part 3 Technical delivery conditions for normalized/normalize
  • AS 2382:1981 Surface roughness comparison specimens
  • BS 4.1:2005 Structural steel sections. Specification for hot-rolled sections
  • JIS G 3136:2005 Rolled steel for building structure
  • ASTM A193/A193M:2009 Standard specification for alloy-steel and stainless steel bolting materials for high temperature o
  • AS 1627.7-1998 Metal finishing - Preparation and pretreatment of surfaces - Hand tool cleaning of metal surfaces
  • EN 12812:2008 Falsework - Performance requirements and general design
  • AS 2074:2003 Cast steels
  • JIS G 3132:2005 Hot-rolled carbon steel strip for pipes and tubes
  • JIS G 3114:2008 Hot-rolled atmospheric corrosion resisting steels for welded structure
  • AS 1163-1991 Structural steel hollow sections
  • AS 1110.1-2000 ISO metric hexagon bolts and screws - Product grades A and B - Bolts
  • AS 2673:1983 Paints for steel structures - Alkyd/micaceous iron oxide
  • AS 1418.1-2002 Cranes hoists and winches - General requirements
  • AS 1627.2-2002 Metal finishing - Preparation and pretreatment of surfaces - Power tool cleaning
  • ISO 2566.1:1984 Steel - Conversion of elongation values - Carbon and low alloy steels
  • EN 10025.6:2004 Hot rolled products of structural steels - Part 6 Technical delivery conditions for flat products of hig
  • AS 4100:1998 Steel structures
  • AS 2159:1995 Piling - Design and installation
  • EN 10025.4:2004 Hot rolled products of structural steels - Part 4 Technical delivery conditions for thermomechanical rol
  • BS 7668:2004 Weldable structural steels. Hot finished structural hollow sections in weather resistant steels. Specificat
  • BS 8004:1986 Code of practice for foundations
  • EN 10219.2:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2 Tolerances dim
  • AS 5100.6-2004 Bridge design - Steel and composite construction
  • ISO 9224:1992 Corrosion of metals and alloys - Corrosivity of atmospheres - Guiding values for the corrosivity categorie
  • EN 1993-5:2007 Eurocode 3 - Design of steel structures – Part 5: Piling
  • EN 10029:1991 Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions shape and mass
  • JIS G 3192:2008 Dimensions mass and permissible variations of hot rolled steel sections
  • JIS G 3106:2008 Rolled steels for welded structure
  • AS 1111.1-2000 ISO metric hexagon bolts and screws – Product grade C - Bolts

Other References:

  • NZ Building Code
  • AWS D1.5:2008 Bridge welding code
  • IPENZ/ACENZ. The briefing and engagement of consultants. IPENZ/ACENZ 1994.
  • IIW 2007. XIII-2151-07 Recommendations for fatigue design of welded joints and components. International Institute of Welding.
  • American Institute of Steel Construction Quality criteria and inspection Standards.
  • AREMA. AREMA Manual for railway engineering. Chapter 15. Lanham MD: American Railway Engineering and Maintenance-of-Way Association 2009.
  • NZTA. Bridge manual SP/M/022. 2nd ed. New Zealand Transport Agency 2003.
  • American Petroleum Institute. API 5L Specification for line pipe. 42nd ed. Washington: API 2000.

International Classification for Standards (ICS) is an international classification system for technical standards. It is designed to cover every economic sector and virtually every activity of the humankind where technical standards may be used.

Follow these links to find other Standards similar to the one you are viewing.

Other documents in this suite of Standards

Other people who purchased this product also bought...